I called the multi-way speakers (speakers of other than full range) speakers 2-way or more. In a multi-way speaker, it is usual to use electronic equipment and electric circuit which limits the range range of each unit is not duplicated. There may be driven by a power amplifier separate range for each is divided by (the stage of the voltage signal) before the power amplifier, it is divided into a power amplified by the power amplifier often. Called crossover frequency the frequency corresponding to the boundary of the range of each unit. Crossover frequency there are two one, if the 3-way, if two-way.
Since the mounting position of each unit is different inevitably, there is a position opinion of instruments or voices that blurred as compared to the full range in a multi-way speaker. Speaker system to solve this is to place the two woofers so as to sandwich the top and bottom of the tweeter were matched apparently mounting position has been sold. Called coaxial type (coaxial) with 2-way unit has a 2-way unit with one unit in that as a special case, to incorporate a tweeter in the center of the woofer.
In some cases, the speaker system described above, is added as a separate subwoofer enclosure. This is a dedicated speaker system for issuing only (ultra bass, bass) bass. May say that comes to most of the home theater products, and is widely used as an AV equipment. As for the subwoofer, which may be added LFE channel as (0.1ch) in a system such as Dolby Digital, but are not intended to divide the range of the speaker is in charge, which adds ultra bass as independent channels it is to.
Is referred to as (or simply network) or "crossover network" "Passive Network" split-range electric circuit constituted by only passive elements. Network consists of attenuator due to resistance to adjust the channel divider by the filter of the low-pass high-pass due capacitors and inductors, the imbalance due to the difference in efficiency of the speaker of each band.
The design of the network is not done correctly, the frequency characteristics and phase characteristics deteriorate. It is common for this, something particularly complex is going assembled the best circuit repeatedly listen and measurement.
The principle of the upper phase is fall apart a complex network, or to balance the number of combinations only difficult. Therefore, better sound quality on, but he still split the range or better, more of a simple configuration is about what good, opinion is divided into both the manufacturer, user.
The most important in the design of the network, it is to properly set the crossover frequency. Range that can be played enough to increase by increasing the unit spread, but the design of the network is made difficult by the other hand the crossover frequency increases.
Since the mounting position of each unit is different inevitably, there is a position opinion of instruments or voices that blurred as compared to the full range in a multi-way speaker. Speaker system to solve this is to place the two woofers so as to sandwich the top and bottom of the tweeter were matched apparently mounting position has been sold. Called coaxial type (coaxial) with 2-way unit has a 2-way unit with one unit in that as a special case, to incorporate a tweeter in the center of the woofer.
In some cases, the speaker system described above, is added as a separate subwoofer enclosure. This is a dedicated speaker system for issuing only (ultra bass, bass) bass. May say that comes to most of the home theater products, and is widely used as an AV equipment. As for the subwoofer, which may be added LFE channel as (0.1ch) in a system such as Dolby Digital, but are not intended to divide the range of the speaker is in charge, which adds ultra bass as independent channels it is to.
Is referred to as (or simply network) or "crossover network" "Passive Network" split-range electric circuit constituted by only passive elements. Network consists of attenuator due to resistance to adjust the channel divider by the filter of the low-pass high-pass due capacitors and inductors, the imbalance due to the difference in efficiency of the speaker of each band.
The design of the network is not done correctly, the frequency characteristics and phase characteristics deteriorate. It is common for this, something particularly complex is going assembled the best circuit repeatedly listen and measurement.
The principle of the upper phase is fall apart a complex network, or to balance the number of combinations only difficult. Therefore, better sound quality on, but he still split the range or better, more of a simple configuration is about what good, opinion is divided into both the manufacturer, user.
The most important in the design of the network, it is to properly set the crossover frequency. Range that can be played enough to increase by increasing the unit spread, but the design of the network is made difficult by the other hand the crossover frequency increases.